MICROMVG Image Release History
	Version	Release Date		Changes
	6.08.18	3/26/2008		1. Correction - Standard Steam Calculation
	6.08.17	1/31/2008		1. New Rosemount Average Routine
	6.08.16	2/26/2007		1. Add NIST10 Superheated Steam
				2. Add Yesterday Day and Last Hour Registers
	6.08.15	1/8/2007		1. Modify Display Sensitivity Key Routine
	6.08.14	11/28/2006		1. Add Floating Point Shift Registers
				2. Add Analog Input Expansion Option
	6.08.13	11/9/2005		1. Add Day Flow Time in Minutes
	6.08.12	10/5/2005		1. Add Proving Function
	6.08.11	6/23/2005		1. Increase the Range of Saturated Steam Table
	6.08.10	4/26/2005		1. Add PID Pressure Base
				2. Add Daylight Saving Time Option
				3. Add Multi.Variable Communication Status
	6.08.9	11/30/2004		1. Modify Modbus Shift Routine
				2. Add Battery Voltage Reading
				3. Enable/Disable Front Panel Scan Key
				4. Enable/Disable Display Backlight Function
				5. Correction - V-Cone Y Factor
				6. Add Calibration Parameters to be Part of the Configuration Software
	6.08.8	9/17/2004		1. Increase the Range of Saturated Steam Table
				2. Synchronize the System Clock and Realtime Clock
	6.08.6	6/15/2004		1. Add New Modbus Shift Range (8001-8451)
	6.08.5	6/8/2004		1. Increase Stack
				2. Correction - Frequency Input - Mass Pulse FWA Routine
	6.08.4	4/20/2004		1. Correction - Broadcast Command
	6.08.3	4/15/2004		1. Correction - Analog Ouput - Reverse Flow Rate
	6.08.2	3/26/2004		1. Add Yesterday's Data Modbus Registers (8381-8435)
	6.08.1	10/27/2003		1. Set ROM Wait State to 1
	6.08.0	10/7/2003		1. Correction - Analog Output #2,#3,#4
				2. Correction - Modbus Registers 1801-1846
	6.07.9	9/19/2003		1. Correction - RS232 Communication (Version 6.07.8 only)
	6.07.8	9/8/2003		1. Reset Multi.Variable if Multi.Var. Communication is Lost
				2. Set RAM Wait State to 1
	6.07.7	11/15/2002		1. Normalize AGA8 Composition Percentage. (Acceptable Data Range 98-102)
	6.07.6	10/3/2002		1. Correction - Steam Entropy Calculation
	6.07.5	9/6/2002		1. Incrase DP Range of Multi-Variable to 1075
	6.07.4	8/26/2002		1. Correction - Analog Input Jumping
	6.07.3	3/15/2002		1. Disable Calibrate Mode - Mass Flow Rate Data Entry
	6.07.2	1/23/2002		1. Revise AGA8 Routine
	6.07.1	1/3/2002		1. Set Wait State to 2
	6.07.0	10/17/2001		1. Correction - RTD Calibration
	6.06.9	8/20/2001		1. Correction - Analog Output Maximum
	6.06.8	7/17/2001		1. Revise Communication Routine
	6.06.7	7/10/2001		1. Correction - Analog Output Drop
	6.06.6	6/10/2001		1. Correction - RTD Reading (Increase RTD Gain)
	6.06.5	5/8/2001		1. Disable Analog Output if Calibration Is Set
	6.06.4	4/23/2001		1. Correction - Density.b Calculation (AGA8 Gross Method#1/#2)
				2. Add New Modbus Registers - Analog Output#3/#4
	6.06.1	4/15/2001		1. Add PID Control Routine
	6.06.0	4/5/2001		1. Add Analog Output #1-#4 Routine
	6.05.3	3/23/2001		1. Increase Sensitive Factor Value
	6.05.2	3/16/2001		1. Add New Data Entry - FA Override (V-Cone Calculation)
	6.05.1	2/7/2001		1. Swap Status Input/Switch Output #1/#4 Setting
	6.05.0	11/23/2000		1. Revise Multi-Variable Interface Routine
	6.04.0	10/23/2000		1. Add More Resolution to Totalizer
	6.03.4	10/10/2000		1. Correction - Switch Outputs and Alarms
	6.03.3	10/6/2000		1. Correction - Spare Data Alarms
				2. Set Data Ready Flag After Retrieving Historical Data
	6.03.2	9/22/2000		1. Correction - Multi-Variable Calibration
	6.03.1	9/5/2000		1. Correction - Analog Output Default
	6.03.0	8/21/2000		1. Add Calibration
				2. Correction - Display Contrast
	6.02.0	8/12/2000		1. Add Modem Function
	6.01.0	8/4/2000		1. Correction - Calibration Mode